|
Model APT is a low-profile apartment house operator that features a resilient-mount motor, low-profile design, industrial ball bearings on the output shaft, quiet-gliding rail spacers, auto-reconnect trolley assembly with nylon inserts and a standard solenoid brake.
LOGIC 3.0 TECHNOLOGY (L3)
Added Value
- Built-in 3-channel, 315MHz radio receiver accepts up to 23 Security+® or unlimited DIP switch remotes. 3-button remotes can be programmed for OPEN/CLOSE/STOP operation
- Maintenance Alert System™ establishes a routine maintenance schedule based on the number of cycles or calendar date. Includes self-diagnostic system that allows you to troubleshoot up to eight different error codes
- Timer-to-Close allows programming in 5-sec or 1-min increments - commercial or industrial photo-eyes required
- Thermal motor overload can be easily reset from the 3-button floor level control station
Reliability & Programming Simplicity
- Switchless motor eliminates stuck start switch and motor malfunctions on single-phase operators
- All high-voltage connections have been removed from the board for safety and ease of service
- Diagnostic LEDs speed installation and troubleshooting
- Motor direction jumper lets you change motor direction by simply moving a jumper
Available Plug-in Options for Logic 3.0 (L3)
Auxiliary Contact: Used to operate security, warning, heating or other 5V to 240V devices. Features both normally open and closed contacts that actuate in conjunction with limit switches.
Warning Signal: Red/green light module provides safety warning prior to close (when using timer-to-close feature). System also supports audio warning devices and includes down mid-stop feature.
CPS3 Option: Enables the addition of a second set of photo-eyes or 2- or 4-wire, self-monitoring edge.
STANDARD FEATURES
Motor: Continuous-duty high-starting torque motor with instant reverse and overload protection. Available in 1/2 single phase capacitor start motors. Removable without affecting limit switch settings.
Drive Reduction: First-stage heavy-duty 4L V-belt; second and third stages #41 chain; output on trolley #48 chain.
Wiring Type: All operators are factory preset to C2 wiring providing momentary contact to open and stop, with constant contact to close. Momentary contact to close (B2 wiring) can be easily set. T and TS wiring can be activated with use of the CPS-L or CPS-LN4. Failsafe wiring can be selected with the addition of a CPS-L, CPS-LN4 or failsafe edge and CPS3 card. The operator is pre-wired to accept a sensing device, photoelectric sensors, radio controls and most types of access control equipment.
Maximum Run Timer: Standard feature that protects against damage to the door and operator. Any time a closing door takes 10 seconds more than its programmed standard cycle time, the door will stop.
Programmable Mid-Stop: Allows the door to sop at mid-point during open travel.
Delay-on-Reverse Circuit: A one-second delay-on-reverse circuit to prevent premature door and operator wear.
Low-Profile Design: Low-profile design can be ceiling-mounted for low headroom applications.
External Radio Control Terminal: Quick, convenient connections for retrofitting or adding radio controls on logic or mechanical operators.
Bearings: Industrial ball bearings on the output shaft; heavy-duty, oil-filled on reduction shafts.
Friction Clutch: Adjustable, helps protect against major damage to door and operator should the door meet an obstruction.
Construction: NEMA 1 type electrical box, heavy-duty 11-gauge steel frame with durable powdercoat finish, all reduction sprockets drilled and pinned to shafts.
Push Button Station: 3-button station comes standard and has OPEN/CLOSE/STOP functionality.
Rail Assembly: High-strength dual L-rail track and quick-mount header bracket which provides fast, swing-up installation.
Warranty: 2-year warranty.
CONTROL ACCESSORIES
CPS® Commercial Protector System®: (recommended) A "non-contact" photo safety sensor designed to sense an obstruction and signal the door operator to reverse to open.
Sensing Edge: (recommended) Designed to sense an obstruction and signal door operator to stop or reverse as desired. Either an electric or pneumatic sensing device can be added to bottom edge of door.
|
